All: Reproduction Ford Parts

Ford Applications Using D4TZ-3600-A Steering Wheel & D3TZ-13A805-A Horn Pad Servicing the steering column on classic Ford vehicles often requires removing the steering wheel assembly. When working with steering wheel D4TZ-3600-A and horn pad D3TZ-13A805-A applications, the process is straightforward when approached in the correct sequence and with the proper tool. This guide outlines the removal procedure based on original shop notes and preserves the mechanical order of operations. Application Scope Applies to Ford vehicles equipped with: D4TZ-3600-A Steering Wheel D3TZ-13A805-A Horn Pad TOOL-3600 Steering Wheel Puller Application may vary by model year or steering column configuration. Always confirm fitment before ordering replacement components. Original Shop Notes Remove two screws holding horn pad Undo wiring clips for horn pad Loosen steering wheel nut Attach steering wheel tool Loosen wheel Remove tool and nut Remove wheel Step-By-Step Technical Interpretation 1. Remove Horn Pad Retaining Screws The horn pad is secured to the steering wheel by two screws. Removing these fasteners allows access to the internal wiring and steering wheel retaining nut. Use appropriate screwdriver to avoid damaging the screw head. 2. Disconnect Horn Pad Wiring Clips With the horn pad removed, carefully release the wiring clips connected to the horn contact assembly. These clips must be detached before steering wheel removal to prevent wire strain or terminal damage. 3. Loosen the Steering Wheel Retaining Nut Loosen the steering wheel nut but do not remove it completely at this stage. Leaving the nut partially threaded helps protect the steering shaft threads during puller use. 4. Install Steering Wheel Puller (TOOL-3600) Attach the steering wheel puller evenly to the threaded mounting holes in the wheel hub. The puller applies controlled pressure to separate the steering wheel from the tapered steering shaft. Using a puller prevents damage to the wheel hub and avoids stressing the column bearings or shaft splines. 5. Release the Steering Wheel from the Shaft Once the puller is properly secured, gradually tighten the tool until the steering wheel breaks free from the taper. After the wheel loosens, remove the puller and fully remove the steering wheel nut. The steering wheel can then be lifted off the column shaft. When Steering Wheel Removal Is Necessary Steering wheel removal is typically required during: Turn signal switch service Steering column restoration Column bearing inspection Steering wheel replacement Because the steering wheel is mounted on a tapered shaft, proper tool use is recommended to avoid damage. Restoration Considerations On older Ford steering columns, corrosion or age can increase resistance between the wheel hub and shaft taper. Controlled puller pressure is preferable to prying or hammering methods. Inspect wiring connectors and horn contacts while the assembly is disassembled. Access during wheel removal provides an opportunity to evaluate column components without additional tear down. Confirm steering column configuration and model year before ordering steering wheels, horn pads, or related steering components. Explore our full selection of classic Ford steering wheels, horn pads, and steering column components.

Flathead V8 Water Pump & Mount Service Guide1937–1948 Ford Passenger Car | 1939–1948 Mercury V8 Servicing the cooling system on a 1937–1948 Ford passenger car or 1939–1948 Mercury V8 requires more than just swapping a part. The flathead platform integrates the water pumps, front engine mounts, and cooling hoses in a way that makes access and sequencing important. Whether you’re replacing water pumps, water pump bolts, or addressing motor mounts at the same time, the process benefits from a clear plan. The parts referenced here include: 78-8501-PR – Water Pumps 78-8501-HK – Water Pump Bolts 78-6038-BDK – Motor Mounts These components are commonly serviced together on 37–48 Ford and 39–48 Mercury V8 applications due to their physical proximity and shared mounting areas. Why These Systems Overlap On these flathead V8 engines, the water pumps mount at the front of the block and are positioned near the front motor mount assembly. In many cases, removing the pumps requires relieving load from the mounts. Aging rubber mounts can sag over time, changing engine position slightly and complicating pump removal or installation. Addressing motor mounts during cooling system service can help maintain proper engine alignment. Fitment may vary slightly by model year or chassis configuration. Always confirm application for Ford passenger car versus Mercury V8 before ordering parts. Give us a call or email and we will answer your questions! Basic Removal Sequence A structured approach reduces stress on hardware and surrounding components: Drain CoolantBegin by fully draining the cooling system. Open the radiator petcock and, if equipped, block drains to remove as much coolant as possible. Remove Radiator Hoses (Upper and Lower)Disconnect both hoses from the radiator and water pump outlets. Inspect hose condition during removal. Loosen Motor Mount BoltsThe front motor mount assembly may need to be loosened to allow slight engine movement. Do not fully remove the mount until the engine is properly supported. Support the EngineCarefully jack up the engine using a wood block under the oil pan. The wood block helps distribute load. Raise only enough to relieve tension from the mounts. Remove All Eight Water Pump BoltsEach pump is secured with multiple bolts. Remove all mounting hardware evenly to prevent binding. The water pump bolt kit (78-8501-HK) ensures proper hardware replacement if originals are corroded or worn. *PRO TIP there is a bolt in each of the lower water pump outlets. Once the bolts are removed, the water pumps (78-8501-PR) can be removed from the block. Surfaces should be cleaned thoroughly before re-installation. Motor Mount Considerations The motor mount kit (78-6038-BDK) supports the engine’s front weight and isolates vibration from the frame. When mounts are deteriorated, engine position may shift slightly. Replacing mounts during water pump service is practical because access is already established and the engine is supported. Fitment should always be verified for specific Ford passenger car or Mercury V8 applications within the 1937–1948 and 1939–1948 ranges. Restoration-Focused Approach Flathead cooling system service is straightforward when handled methodically. These engines were designed for serviceability, but age introduces corrosion, hardware fatigue, and rubber deterioration. Replacing water pumps, water pump bolts, and motor mounts as a coordinated service helps maintain structural alignment and cooling integrity. Taking the time to follow proper removal steps protects original components and ensures the flathead V8 continues operating as intended. View our full selection of Flathead V8 Water Pumps and Cooling Components.

INTRODUCING A NEW ITEM, THE 1959 PASSENGER AND RANCHERO PARK LIGHT HOUSINGS!  

There’s nothing like the sound of a 289 V8 with a four-barrel carburetor purring down the street. When you’ve got the ponies galloping under the hood of a 1966 Mustang, it doesn’t matter if the sun is shining or the rain is pouring - it’s a beautiful day when you’re behind the wheel of a classic. Classic cars, especially ones like the Mustang, are always head turners. It’s no wonder your car sounds good. You’ve kept your beauty running smoothly with classic Mustang parts whenever you need to replace something. Sometimes, when you own a classic, just like with the newer model cars, a problem can develop unexpectedly. The problems can be small or large. For example, you might start to notice that your Mustang doesn’t have the same gallop it used to have. You don’t see what the problem is until one day, you see smoke like you’ve never seen before. When you see white smoke coming from the exhaust of the car, you need to get it home and check the dipstick to see if there’s a distinctive milky appearance in the oil. That could mean a blown head gasket. When you realize that there’s a blown head gasket, you know that in order to get the car up and running in the best of shape, you’ve got to find an auto store that sells classic Mustang parts. You may not have one local, you may have to order online, but whatever you have to do to get parts for your car, it’s worth any effort. You don’t want to compromise with just any parts seller, come to the best here at C&G Ford Parts! A lot of times, you’ll see shops advertise that their replacement parts for your classic car are so “identical looking” that you can’t see a visual difference. You may not be able to see a visual difference with a knock off part, but you can certainly tell a difference in how the car runs and in how long that part will last. Buying classic Mustang parts isn’t just for when you need to fix something on the car. These are what car enthusiasts look for when they’re restoring a classic to its former glory - and if you ever decide to sell you car, it should have parts made just for it. It doesn’t matter if it’s a small job like replacing your gas cap or a big job like replacing the windshield seal - you’ll get more mileage and less headaches by choosing classic Mustang parts from C&G Ford Parts, always choose the best.

As a classic Ford enthusiast, my journey in the realm of restoration has been nothing short of exhausting. The thrill of bringing a vintage beauty back to its former glory is unparalleled. However, this passion comes with its challenges, the most significant being sourcing the right parts. This is where classic reproduction Ford parts have become a game-changer for someone like me. For years, the pursuit of authentic, original used and NOS parts was akin to searching for a needle in a haystack. These parts, often scarce and very expensive, could mean the difference between a stalled project and a triumphant restoration. Then entered the world of reproduction parts – a world that has not only made restoration more accessible but also more reliable. Initially, I was skeptical about using reproduction parts. Would they fit correctly? Would they maintain the authentic look and feel of my classic Ford? These concerns, however, were quickly dispelled. Modern reproduction parts are crafted so that they seamlessly blend with the original components. Manufacturers use advanced technologies and materials to replicate parts. One of the biggest advantages I've experienced with reproduction parts is the availability of parts. Unlike original parts, which may have undergone decades of wear and tear, reproduction parts are brand new and often incorporate modern engineering improvements. This doesn't just bring peace of mind; it enhances the driving experience, making it safer and more enjoyable. From a cost perspective, reproduction parts are generally more affordable than their NOS counterparts. This affordability has allowed me to allocate resources to other aspects of restoration, like professional paint jobs or interior refurbishments. Moreover, the availability of these parts means less time scouring swap meets and more time in the garage, doing what I love. In conclusion, classic reproduction Ford parts have transformed the restoration landscape for enthusiasts like me. They bridge the gap between the past and the present, ensuring that the legacy of classic Fords continues to cruise down our roads, not just reside in our memories. They are a testament to the evolving nature of car restoration, blending tradition with innovation, and keeping the spirit of classic Fords alive and roaring.

Since you buy all your classic Ford parts from us, we thought we would enlighten you to a product that you might find useful! Let’s say you’re cruising around town in your Classic Ford… you’re reveling in the number of folks you see looking at your ride (yes your car, not you anymore). You roll to a stop easily and decide to turn the corner and drive down Main Street to see if any of your buddies have made it to the Burger Barn. Suddenly, you feel “clunk” and you KNOW the old Ford didn’t come that way from the factory, so you begin to wonder “Hmmm, what could the old girl need now?”Finishing the cruise you head home and call it a night. Next day you’re up and at ‘em, headed out to the garage. You whizz past your wife in your grubby's and wonder for a moment why she has a big grin on her face, “Oh well, she musta been on the phone” you figure. With a big grin on your face and a wave to the wife, you whistle out loud as you head out the door thinking, “I’ll be at this most of the day” After organizing your tool box and getting everything ready for troubleshooting you begin to diagnose what could be ailing your “baby”. After troubleshooting for a while, you begin to realize that the bushing in the upper steering tube has worn out. It turned to rock and the steering shaft is wobbling around in the tube causing the clunk you felt last night. “Well, that’s a relief” you gush, “I don’t need to tear apart the front end!” “I wonder if Ford has a warranty recall on those” you chuckle to yourself as you pull your dog eared copy of your trusty C&G Ford Parts catalog off the shelf. You see that there is a replacement rubber upper bushing that often gets worn out over the years. “Just what I need” you think. “Hold the phone, what’s this?” you spot a new- fangled “kit” that only C&G has! This Upper Steering tube bearing kit includes bearing, spring, and bushing sleeve that replaces the original rubber bushing for a longer lasting, easier turning, tight fit. The kit includes a diagram to show you exactly where to install the parts, and in it what order. “Excellent” you whistle. So you pick up the phone, call C&G and after speaking to some friendly and knowledgeable parts folk, you have your kit on the way. A couple days later, your classic Ford parts show up and you’re ready to install the new B-3517-K kit you ordered. Remove the steering wheel. Remove original rubber bushing from over worm shaft. Install in this order- bearing , sleeve , spring. Make sure the tapered ends are facing down on both bearing and sleeve, drive the bearing down the worm shaft about 3/4" with a large socket, then let sleeve follow. Finally, put spring over worm shaft, in-between the sleeve and the steering wheel. Put steering wheel back on and tighten down the steering nut. No more play in the upper part of the column! Steering Tube Bearing Kit B-3517-K

Classic Ford parts are essential components for enthusiasts and collectors who aim to restore, maintain, or customize their vintage Ford vehicles. Ford, one of the most iconic automakers in history, has produced a range of classic cars that have a special place in the hearts of many. From the legendary Model T to the Mustang, the legendary F series pick ups and Mercury's each classic Ford model has its unique set of parts and accessories that are sought after by collectors and restorers worldwide. The allure of classic Ford parts lies in their ability to bring a piece of automotive history back to life. These parts are not just replacements; they are fragments of a bygone era, each with a story to tell. Restoring a classic Ford using reproduction parts is like preserving a piece of art. It's about maintaining the integrity and authenticity of a vehicle that has been a symbol of American culture and innovation. One of the challenges in restoring classic Fords is finding the right parts. Authentic parts are often scarce, and locating them can be a painstaking process. Fortunately, C&G Ford Parts has made it easier for enthusiasts and restorers to find what they need. We have have a vast inventory of reproduction parts, from crank pulleys to dash bezels, and we cater to a range of models and years. The quality of classic Ford parts is paramount. Authentic parts are typically more durable and fit better than aftermarket replicas, but are very hard to find. Reproduction parts on the other hand ensure that the vehicle remains true to its original form, which is crucial for maintaining its appeal. For those who cannot find authentic parts, high-quality reproductions are the next best option. These parts are manufactured to match the original specifications as closely as possible. For many, the restoration of a classic Ford is more than a hobby; it's a passion. It involves meticulous work and a deep appreciation for the craftsmanship and engineering of a bygone era. Whether it's a complete restoration or a minor repair, using classic Ford parts is essential to keeping the legacy of these timeless vehicles alive. As these cars continue to age, the demand for high-quality classic parts is only expected to grow, making them an integral part of the classic car community.

The world of classic Ford parts is a niche fueled by a unique blend of nostalgia, engineering marvel, and a deep-seated passion for automotive history. This niche isn't just about maintaining or restoring old vehicles; it's about preserving a legacy, a piece of Americana that has shaped and been shaped by decades of innovation and culture. At the heart of this niche are the classic Fords themselves - from the groundbreaking Model T, the first car to be mass-produced, to the Mustang, an icon of American muscle and the F series pick ups which supply the backbone of America. Each model represents a different era, a distinct style of engineering and design. Restoring these vehicles is more than a hobby; it's a journey back in time, an attempt to capture the essence of an era long gone. For those immersed in the classic Ford parts niche, the hunt components is a significant part of the excitement. These enthusiasts spend countless hours searching through auto flea markets, online forums, and specialty shops for that perfect part. The joy of finding a rare, original component can be as exhilarating as driving the restored vehicle itself. The community aspect of this niche is incredibly strong. Across the world, classic Ford owners and restorers come together, both online and in person, to share stories, exchange knowledge, and offer support. Car shows and meet-ups turn into celebrations of these automotive treasures, where the beauty and craftsmanship of classic Fords are displayed with pride. Moreover, the classic Ford parts niche is not just about the past; it's about sustainability. In a world increasingly concerned with environmental impact, restoring and maintaining older vehicles is a form of recycling, giving new life to old Fords that might otherwise be forgotten relics. In essence, the classic Ford parts niche is more than a collection of old cars and their components. It's a testament to the enduring impact of Ford's innovations on automotive culture. It's a community bound by a shared passion for the art of restoration, a reverence for history, and the thrill of bringing a piece of that history back to life. For many, it's not just a hobby; it's a way of connecting with the past and preserving it for future generations. Here at C&G Ford Parts we specialize in reproduction Ford parts.