Classic Ford Maintenance

Turn Signal Switch Removal & Replacement

Turn Signal Switch Removal & Replacement Guide

Classic Ford Mustang, Falcon, Fairlane, Comet & F-Series Trucks (1960s–1970s)

If your turn signals are acting up—or just plain dead—it’s often the switch inside the column calling it quits. The good news? This is a very doable repair with basic tools and a little patience. Below is a step-by-step guide to replacing classic Ford turn signal switches, including popular part numbers like C3OZ-13341-B, C5OZ-13341-B, C5OZ-13341-HQ, C9TZ-13341-C, and C9TZ-13341-USA.

Why Replace Your Turn Signal Switch?

A worn or failing turn signal switch can cause:

Intermittent or non-functioning signals
Brake light issues
Horn malfunctions (shared circuit in many models)

Replacing it restores proper electrical function and keeps your classic Ford safe—and road legal.

Tools & Prep

Steering wheel puller (TOOL-3600)
Small crescent wrench
Screwdrivers
Dielectric grease
Phone (for reference photos—trust me on this one)

First rule: Disconnect the battery ground cable. Always.

Step-by-Step Removal

1. Remove the Turn Signal Lever

Twist the lever out. If it’s stubborn, use a small crescent wrench on the flat spot found on most originals.

2. Remove Horn Button or Ring

Push down and turn left to release.
⚠️ Go slow—there’s a spring underneath that likes to make a break for freedom.

Inspect horn ring retainer
Remove horn brush if equipped

3. Pull the Steering Wheel

Use your steering wheel puller (TOOL-3600) and set the wheel aside.

4. Document Wiring (Critical Step)

Before disconnecting anything:

Take clear photos of wire routing and colors
Or write them down if you're going old-school

Some 1965+ models use connectors that may require a release tool.

5. Disconnect Wiring Under Dash

Unplug the turn signal switch harness from beneath the dash.

6. Remove the Turn Signal Switch

Back at the column:

Remove the (3) mounting screws ONLY
Do NOT remove the two large nuts (unless you enjoy fishing dropped studs out of a column…)

Carefully pull the switch upward while feeding the wires out of the column.

Installation Process

7. Compare Old vs New Switch

Before installing:

Match wire colors and count
Confirm lever compatibility

8. Install New Switch

Feed wires down through the column
Seat the switch properly
Reinstall the (3) retaining screws

9. Reconnect Wiring

Plug into under-dash harness
Apply dielectric grease to connections for longevity

10. Reassemble Column

Reinstall steering wheel
Install horn brush (if applicable)
Replace spring, horn button/ring
Thread in turn signal lever (don’t over tighten)

Final Check (Moment of Truth)

Reconnect the battery.

Now…

No smoke? Good sign.
No weird noises? Even better.

Turn the key and test:

Turn signals
Brake lights
Horn

If everything works—you nailed it.
If not… well… time to retrace those wiring steps.

Pro Tips from the Shop Floor

Always photograph wiring before disassembly—memory lies, photos don’t
Replace worn horn components while you’re in there
Use dielectric grease to prevent future corrosion issues
Never force the switch or lever during install

Need the Right Turn Signal Switch?

At C&G Ford Parts, we’ve been helping restorers get it right since 1978. Every part we carry is built for proper fitment and factory-correct function—because guessing doesn’t belong in a restoration.

👉 Browse our selection of classic Ford turn signal switches and get your signals back in sync.

Leave a comment

Please note, comments need to be approved before they are published.

Name

Email

Comment

Old Ford Cars

The Iconic 1965 Ford Mustang

The Iconic 1965 Ford Mustang The Ford Mustang, a name that resonates with freedom, power, and style, made its debut in 1964 but it was the 1965 model year that solidified its legend in automotive history. Often celebrated as the car that started the "pony car" era, the 1965 Mustang was not just a vehicle; it was a cultural phenomenon. Design and Style The 1965 Mustang was an immediate hit due to its sleek, long-hood, short-deck design crafted by Lee Iacocca's team. The car's profile was distinctly sporty with a chrome grille, tri-bar taillights, and a fastback version that added an aggressive, almost European flair. Available in coupe, convertible, and fastback body styles, the Mustang could be tailored to suit various tastes, from the conservative to the audacious. Interior options ranged from luxurious with bucket seats and a console to more basic vinyl benches, catering to a broad demographic. Engine Options What made the Mustang particularly versatile was its range of engine choices. At the base, there was a 170 cubic inch inline-six that was economical for daily driving. For those seeking more thrill, Ford offered a trio of V8 options: 200 hp 289 V8 with a two-barrel carburetor. 225 hp 289 V8 with a four-barrel carburetor: This version delivered more punch, enhancing the car's sporty character. 271 hp GT package with a 289 Hi-Po (High Performance): This was the choice for enthusiasts who wanted to experience the raw power under the hood, especially when paired with a 4-speed manual transmission Performance and Popular Culture The Mustang wasn't just about looks and power; it was about accessibility. Priced at around $2,368 for the base model, it was relatively affordable, allowing a wide array of Americans to own a piece of automotive flair. Its introduction timing was impeccable, aligning with the youth culture of the 60s, which celebrated speed, freedom, and individuality. The Mustang found its way into movies, TV shows, and became synonymous with the American dream of the open road Legacy Over the decades, the 1965 Mustang has not only retained its iconic status but has also seen its value appreciate significantly among collectors. The model year is often cited for its pivotal role in shaping car design trends, influencing everything from the muscle car era to modern sports cars. Today, a well-preserved 1965 Mustang, especially in its GT or Shelby versions, can fetch high prices at auctions, reflecting not just nostalgia but appreciation for its design and engineering prowess The 1965 Ford Mustang was more than a car; it was a symbol of a transformative period in American automotive history, embodying the spirit of an era where style, performance, and accessibility collided to create something truly timeless. Whether you're a car enthusiast or not, the Mustang's impact on culture, design, and the automotive industry is undeniable, making it a forever celebrated piece of Americana.

37-41 Old Ford Trucks, Old Ford Car and Old Mercury Car Distributor

Old Ford Cars

INSTALLING A CLASSIC FORD DISTRIBUTOR INTO OLD FORD TRUCKS AND CARS

INSTALLING A CLASSIC FORD DISTRIBUTOR 1932-1941 Old Ford Trucks, 1932-1941 Ford Passenger Cars and 1939-1941 Mercury Cars with original V8 distributor: 1. Check inner caps one at a time to make sure they fit distributor housing, sand them if needed. Also check to make sure once installed rotor does not hit the inner cap. After fitting inner caps put inner and outer caps together with the spark plug wires and set aside. 2. Mount coil to distributor making sure coil brush makes contact with rotor and copper contact is not bent. 3. Make sure the mounting surface is clean and there is nothing in the camshaft slot where the distributor mounts. Check to make sure mounting bolt threads are clean and free of dirt, set bolts on top of engine for easy reach. 4. Time to mount the distributor. Put gasket on base of distributor, you can put a small amount of sealant on the gasket. Place distributor on to timing cover using fingers to turn rotor to make sure distributor is correctly seated in the camshaft. The distributor will mount flat to the timing cover when correctly installed. If the distributor is not seated correctly you can crack the distributor case when you tighten the bolts. Now you can put the three mounting bolts in and tighten. Do not over tighten(snug). 5. Install inner/outer caps to the distributor and pop the bail over to hold in place. 6. Install vacuum line to distributor. 1941-47 (6 Cylinder “G” Engine) Old Ford Trucks and Passenger Cars, 1942-1947 Old Ford Trucks and 1942-1948 Passenger Cars/Mercury Cars (V8): 1. Make sure the mounting surface is clean and there is nothing in the camshaft slot where the distributor mounts. Check to make sure mounting bolt threads are clean and free of dirt, set bolts on top of engine for easy reach. 2. Place the rotor on distributor and mount distributor cap and turn rotor slowly to make sure the rotor does not hit the inner cap. If rotor hits cap lightly file end of rotor till it clears. Remove distributor cap and set aside. Leave rotor on distributor. 3. Time to mount the distributor. Put gasket on base of distributor, you can put a small amount of sealant on the gasket, be sure not to get sealant on vacuum rubber grommet. Place distributor on to timing cover using fingers to turn rotor to make sure distributor is correctly seated in the camshaft. The distributor will mount flat to the timing cover when correctly installed. If the distributor is not seated correctly you can crack the distributor case when you tighten the bolts. Now you can put the two mounting bolts in and tighten. Do not over tighten(snug). 4. Install distributor cap and pop clips on for 42 crab cap. If you have a 46-48 with the inner and outer cap you will have to install plug wires into cap first before installing caps on distributor.

Old Ford Trucks

1979 Ford F150

1979 Ford F150 The 1979 Ford F150 stands as a significant chapter in the storied history of Ford trucks. Known for its durability, classic design, and utility, the '79 F150 is a beloved model among enthusiasts of classic Ford automobiles. Specifications Engine Options: The 1979 F150 came with various engine options, including: 4.9L 300 Inline-6: A reliable workhorse known for its longevity. 5.0L 302 V8: Offered a balance of power and efficiency. 5.8L 351M V8 and 6.6L 400 V8: These larger engines were preferred for heavier towing and payload capacities. Transmission: Standard: 3-speed manual. Optional: 4-speed manual and 3-speed automatic. Dimensions: Wheelbase: Ranged from 117 inches (regular cab, short bed) to 155 inches (SuperCab, long bed). Length: Varied based on the model, from 188.5 inches to 235 inches. Width: Approximately 79 inches. Towing and Payload: Depended on the engine and configuration, with the larger engines supporting greater capacities. Part Numbers: Locating specific part numbers for a vehicle as old as the 1979 F150 can be challenging. However, some common parts include: Brake Pads: D84-2 Oil Filter: FL-1A Spark Plugs: AGSF32. For more specific parts and their numbers, enthusiasts often refer to vintage Ford parts catalogs or online forums. A great place to get real people to talk parts with, is C&G Ford Parts in Escondido, California. Production Numbers: Ford does not publicly release detailed production numbers by year and model. However, it's known that the F-Series was America's best-selling truck in 1979, contributing significantly to the series' overall sales. The F150's popularity in this era helped solidify its legacy in the Ford lineup. Accessories and Customization: The 1979 F150 was often customized and accessorized, reflecting the owner's needs and style. Popular accessories included: Chrome Bumpers: For enhanced aesthetics. Toolboxes: Fitted in the bed for utility. Lift Kits: Many owners lifted their trucks for off-road capability or for a more imposing road presence. Custom Paint Jobs: Reflecting the era's penchant for personalization. Conclusion: The 1979 Ford F150 remains a beloved classic. Its robust construction, range of engine options, and classic styling have ensured its lasting appeal. While specific part numbers and production figures can be elusive, the truck's impact on the automotive landscape is undeniable. Whether restored to its original glory or customized for modern roads, the '79 F150 continues to be a symbol of Americana and the enduring legacy of Ford trucks.

Turn Signal Switch Removal & Replacement