Tracing back the gears of time, the story of Ford's iconic "P-R-N-D-L"

Old Ford drum brake history and tutorial Pre 1967 old Ford cars and old Ford trucks used a drum brake system. In these systems, pressure applied to the brake pedal is transmitted to the master cylinder, which in turn disperses the energy ultimately to the brakes in each wheel. The master cylinder uses the brake fluid to move the wheel cylinders, which in turn moves the brake shoes in the drum. There is a front and back brake shoe, the rear one for stopping a vehicle in drive and the forward one for stopping a vehicle in reverse. When either shoe is pressed against the anchor pin, the brakes are engaged, and the vehicle comes to a stop. The brake pads form the shoes to the anchor pin so there is no slipping. The padding on the rear brake shoe is typically longer and sometimes made of a different material to allow the shoes to wear at a similar rate, since the rear shoe sees much more use. The brake shoes are secured in the drum with both hardware and return springs, which must meet ideal sizing and tension specifications for your make and model for top brake performance. These parts should be replaced any time you work on the brakes in order to counteract wear and tear that can lead to longer stopping times. Stock brake line hoses will have a rubber lining, while aftermarket hoses are available in a stainless braided wrap to preserve the hose. Whichever type you get, make sure the hoses are the correct thread size and length for your year and model and meet DOT safety standards. The rear wheel drum brakes will also contain the parking brake mechanism and will have a cable to the parking brake. Brake pipe must be double flared and use flared nuts. It can be purchased with the flaring already completed or you can cut your own and flare it yourself, but it should meet or exceed DOT safety standards. Hydraulic brakes will fail if there is a weak point in the system, so make sure all your hose and fittings are SAE rated and correctly installed. If you are unsure after installation, test the brakes at low speed in a safe area, such as your driveway or an empty parking lot before taking the vehicle on the road. Starting in 1967 all old fords have a dual master cylinder. This part separates the wheel hydraulics of the front and rear of the car, so a failure in one will not cause a failure in the other. In vehicles without this feature, a leak anywhere in the brake line will cause the entire brake system to fail. With a dual master cylinder, a leak in the front brake system will not affect the rear and vice versa. This is standard in vehicles made after '67, but it's a good safety upgrade for older classic Fords as well. Many classic Ford owners choose to upgrade their front brake system to disc brakes, or the complete system. Drum brakes can overheat and fail in high braking conditions, such as rapid stops at high speeds or driving downhill on mountainous roads. Disc brakes are open and exposed to the outside air, which prevents overheating and brake failure. While this upgrade is not strictly necessary, it's a good idea if you frequently drive in hilly or mountainous areas. Original Ford brake shoes used asbestos in the brake pads. If you are working on a vehicle with its original brake shoes or if you are uncertain if they are original, wear a respirator rated for asbestos while working and wet the brake pads before opening the drum to prevent the asbestos from becoming air born. When cleaning dust from drum brakes, use a dense filtration system to trap the asbestos and dispose of it properly. You can resurface a drum with minor surface issues, but make sure it stays within factory limits for your year and model. Worn or thin drums can break apart or crack and cause brake failure. If you see excessive wear and tear, replace the drum. If you are replacing a leaking wheel cylinder, it's a good idea to do them all at once, including the master cylinder. If you have had problems with one, you will soon have problems with the rest. In addition, you won't need to remember which cylinder was replaced when for future maintenance if they were all replaced at once. You can use a vacuum bleeder to remove old brake fluid and contaminants. Once you remove the old fluid you can use denatured alcohol followed by air to purge the lines. Vacuum each cylinder, including the master cylinder, and replace the old fluid with new, DOT 3 or 4 fluids. When changing fluid, change the rubber hoses and seals. If you have a combination disc and drum system, only use DOT 4 fluid. To ensure a complete cleaning, vacuum some of the new fluid through as well do catch any missed contaminants. When working on or near the brake line, make sure no petroleum-based liquid, such as gasoline, oil, or mineral oil, encounters the hosing. These oils can break down the rubber and cause hoses to start leaking. Make sure to wash your hands thoroughly before and during working on the brakes system to prevent this, especially if you have been working on other parts of the vehicle. When working on your brakes, make sure to follow safety precautions, use safety rated parts, and check over your work carefully. Drum brakes are a very important part of the machinery, and due to the hydraulic system, can easily lose stopping power or fail if something is wrong, especially without a dual master cylinder. Whether you're doing regular maintenance or upgrading the whole system, working carefully will ensure a successful job for your vehicle.

The 1955 Ford Fairlane: A Classic Icon of American Automotive History In the realm of classic American automobiles, the 1955 Ford Fairlane stands out as a significant model that marked Ford's return to prominence in the auto market. Named after Henry Ford's estate, Fair Lane, in Dearborn, Michigan, the Fairlane was introduced as Ford's premier car for that year. With a new frame and 11" brakes, the Fairlane replaced the Crestline as the flagship offering. Design and Styling The 1955 Fairlane was distinguished by its elegant and modern styling, characterized by a lower, longer, and wider profile compared to its predecessors. It featured a distinctive stainless steel stripe running along its side with striking 2 tone paint schemes, which became a hallmark of the Fairlane models. The car was offered in six different body styles, including two- and four-door sedans, hardtop, and a convertible known as the Sunliner. A standout among these was the Crown Victoria, which boasted a tinted, transparent roof panel, adding a futuristic touch to its design. Engine and Performance The Fairlane came equipped with options for both a 223 cubic inch (3.7 L) straight-six engine, a 272 cubic inch (4.5 L) V8, or a 292 cubic inch V8 (4.8 L) with a 4 barrel carb providing buyers with choices tailored to different performance needs. The V8, in particular, was a point of interest for its power and smooth operation. Transmission options included a Fordomatic automatic or a three-speed manual. Market Impact The introduction of the Fairlane was part of a broader effort by Ford to rejuvenate its lineup and recapture market share from competitors like Chevrolet. The Fairlane was not just a vehicle; it was a statement of Ford's commitment to innovation and style. In 1955, Ford managed to outsell Chevrolet, ending a 20-year streak where Chevy had been the best-selling car in America, a testament to the Fairlane's appeal and Ford's strategic marketing. Features and Accessories Ford emphasized luxury and convenience with the Fairlane. It included features like dual exhaust systems on higher-end models which improved both performance and sound. The car also introduced several firsts, including Ford's first factory-installed air conditioning system, known as "Select Aire," which was optional. Innovations like the panoramic windshields, new for 1955, offered drivers a broader view, enhancing safety and driving experience. Cultural Impact The 1955 Fairlane wasn't just a car; it became an emblem of the era's optimism and love for automotive style. Its design and engineering influenced subsequent Ford models and left a lasting impression on American car culture. The Fairlane's success helped pave the way for future models, including the introduction of the Fairlane 500. Legacy Today, the 1955 Ford Fairlane is celebrated by collectors and car enlthusiasts for its blend of style, performance, and historical significance. Restorations are common, and the car's parts are sought after, with companies like Classic Industries providing a range of reproduction parts for enthusiasts looking to bring their Fairlane back to its original splendor. In conclusion, the 1955 Ford Fairlane was more than just another car on the road; it was a symbol of Ford's resurgence and a reflection of the vibrant automotive culture of the 1950s. Its design, performance, and the enduring legacy it left behind continue to make it a beloved piece of automotive history.

Owning or restoring a Ford F100 means that you’ll need easy access to Ford F100 parts whenever you need them. You want the right parts to keep your classic humming along for as long as you own it. If you’ve had your Ford for several years, then you probably already know where to get your hands on Ford F100 parts when you need them. If you don’t know because you haven’t had any issues with the truck until now, there are a lot of different ways you can find what you need. Check out places where other classic vehicle enthusiasts gather and talk to them. You can find groups that hang out on or offline. In some towns, the local drive-in restaurant has an area where classic car owners will gather on the weekends in order to show off their cars. The best place that you can buy Ford F100 parts is from an online store where the employees know about older model cars and trucks and can easily locate or order exactly what you need and ship it right to your doorstep. C&G Ford Parts fits that bill nicely. If you’ve already diagnosed the issue with your Ford and know exactly what part it is that you need, then getting it is going to be fairly simple. But, if like a lot of people, you don’t have in depth knowledge about what could be causing your truck’s issue, the pros can help if they specialize in classic car parts. Many of the employees in a classic auto part business have a love and admiration for the classics and they really know the older vehicles inside and out. Plus, by serving a lot of classic car owners when they have needs, this business more than likely has a lot experience with a wide range of vehicle problems. They may have heard all kinds of stories about what’s going on with the Ford truck and helped other owners with the right Ford F100 parts. Not only will the site know what you’re looking for, but a lot of times, if you ask them how to put a part on, they can tell you how or share online video tutorials with you and save you time. You gain the benefit of their parts knowledge as well as their mechanical knowledge for the same price. What they may suggest and you may find helpful, is to get a catalog of the parts that they do carry so that you’ll have a listing of the parts and the prices. For most classic vehicle owners, they want their F100 truck in pristine condition inside and out. Getting a part that’s “good enough” isn’t enough, they want the best Ford F100 parts.