OLD FORD CARS

Steering Wheel Removal Guide

Ford Applications Using D4TZ-3600-A Steering Wheel & D3TZ-13A805-A Horn Pad

Servicing the steering column on classic Ford vehicles often requires removing the steering wheel assembly. When working with steering wheel D4TZ-3600-A and horn pad D3TZ-13A805-A applications, the process is straightforward when approached in the correct sequence and with the proper tool.

This guide outlines the removal procedure based on original shop notes and preserves the mechanical order of operations.

Application Scope

Applies to Ford vehicles equipped with:

Application may vary by model year or steering column configuration. Always confirm fitment before ordering replacement components.

Original Shop Notes

Remove two screws holding horn pad
Undo wiring clips for horn pad
Loosen steering wheel nut
Attach steering wheel tool
Loosen wheel
Remove tool and nut
Remove wheel

Step-By-Step Technical Interpretation

1. Remove Horn Pad Retaining Screws

The horn pad is secured to the steering wheel by two screws. Removing these fasteners allows access to the internal wiring and steering wheel retaining nut. Use appropriate screwdriver to avoid damaging the screw head.

2. Disconnect Horn Pad Wiring Clips

With the horn pad removed, carefully release the wiring clips connected to the horn contact assembly. These clips must be detached before steering wheel removal to prevent wire strain or terminal damage.

3. Loosen the Steering Wheel Retaining Nut

Loosen the steering wheel nut but do not remove it completely at this stage. Leaving the nut partially threaded helps protect the steering shaft threads during puller use.

4. Install Steering Wheel Puller (TOOL-3600)

Attach the steering wheel puller evenly to the threaded mounting holes in the wheel hub. The puller applies controlled pressure to separate the steering wheel from the tapered steering shaft.

Using a puller prevents damage to the wheel hub and avoids stressing the column bearings or shaft splines.

5. Release the Steering Wheel from the Shaft

Once the puller is properly secured, gradually tighten the tool until the steering wheel breaks free from the taper. After the wheel loosens, remove the puller and fully remove the steering wheel nut.

The steering wheel can then be lifted off the column shaft.

When Steering Wheel Removal Is Necessary

Steering wheel removal is typically required during:

Turn signal switch service
Steering column restoration
Column bearing inspection
Steering wheel replacement

Because the steering wheel is mounted on a tapered shaft, proper tool use is recommended to avoid damage.

Restoration Considerations

On older Ford steering columns, corrosion or age can increase resistance between the wheel hub and shaft taper. Controlled puller pressure is preferable to prying or hammering methods.

Inspect wiring connectors and horn contacts while the assembly is disassembled. Access during wheel removal provides an opportunity to evaluate column components without additional tear down.

Confirm steering column configuration and model year before ordering steering wheels, horn pads, or related steering components.

Explore our full selection of classic Ford steering wheels, horn pads, and steering column components.

Leave a comment

Please note, comments need to be approved before they are published.

Name

Email

Comment

General

Classic Ford Parts for Classy Old Fords

Classic Ford Parts for Classy Old Fords Seeing a vintage Ford gleaming in the sun at a local car show is a treat for the eyes, but even these beautiful vehicles need parts to keep them running smoothly. When something does go wrong with the vehicle, you need to find a store like ours – some place that understands the intricacies of troubleshooting and replacing old Ford parts and understands the mindset of the early Ford owner. You need to know that our selection covers 1932 through 1972 Old Ford cars and 1932 through 1979 old Ford trucks. We ship worldwide Monday through Friday. Unfortunately, you probably already personally experienced, and know all too well, what happens when you walk into a chain auto parts store looking for a part for a 1932 anything that Ford rolled off the assembly line. You’ll get a blank look for your asking. You might get lucky and the counter person will do a google search followed by a “no” if you’re lucky, or a shoulder shrug if you’re not. That’s because these shops carry more parts for current vehicles less than 10 years old and practically nothing for the Old Fords. So as a proof of concept; plug all the information about what you need for your vehicle into the online search area of a chain auto parts store, you’ll see no results and you’re back to square one. You can save yourself a lot of time and frustration by going straight to people like Kyle, Lee, Kristian or Joe – folks who know how important classic Ford parts are and exactly how to get those quality reproduction parts into your hands. People who own vintage Ford vehicles themselves. That’s one of the reasons we have over 200 vendors and tens of thousands of parts on the shelf, so that these vehicles get the right parts they need and will keep running long after other makes are sitting on the sidelines. When it comes to working on these old Ford vehicles, we have what you need, the folks who understand what you need and the "how it works", as well as the ability to get it to you fast anywhere in the world. Whether it’s a 1956 F100 truck and you need a windshield seal, or, a 1940 Ford car and it’s a tie rod, you’ll have to look no further than C&G Ford Parts. On the web or on the phone or even if you drop by and chew the fat at the parts counter, we know what classic Ford parts you need. So, forget the aftermarket big car parts chains and come experience good old fashioned customer service and quality know-how.

Tail Light Harness Replacement Guide for 1960–1965 Falcon, Ranchero, and Comet Wagons

Why This Job Matters This isn’t just about lights—it’s about safety and reliability. A fresh harness eliminates voltage drops, intermittent faults, and those “works when it feels like it” gremlins. It’s one of those upgrades that doesn’t show at the car show, but you’ll feel it every time you drive.