Engine specs for the 1979 Ford F150

1979 Ford F150 in blue, front quarter view

Engine specs for the 1979 Ford F150

The 1979 Ford F150 trucks marked the end of the sixth generation of the rugged F-Series pick up trucks, which spanned from 1973 to 1979. Characterized by its design and durability, the 1979 F150 came with a variety of engine options to suit different needs, from more fuel-efficient six-cylinders to powerful V8s.

Here's a breakdown of the engine specifications for all models of the 1979 Ford F150:

  • 4.9L Inline-6 (300 CID): This engine was the base option for many F-150s, known for its reliability and decent fuel efficiency for the time. It produced around 114 horsepower and 223 lb-ft of torque.
  • 5.0L V8 (302 CID): A step up in terms of power, the 302 V8 offered a balance of performance and fuel economy, making around 140 horsepower and 239 lb-ft of torque.
  • 5.8L V8 (351 CID) Windsor: The 351 Windsor was another popular V8 option, known for its robustness and torque. It delivered approximately 150 horsepower and 265 lb-ft of torque.
  • 5.8L V8 (351 CID) Modified (M): The 351M, often confused with the Cleveland, was a variant designed for torque more than outright power, with similar horsepower to the Windsor but different in technical specifications.
  • 6.6L V8 (400 CID): The 400 was essentially a 351M with a longer stroke, offering more torque at lower RPMs, making it ideal for towing and heavy-duty applications. It produced around 158 horsepower and 277 lb-ft of torque.
  • 7.5L V8 (460 CID): Available in certain models and regions, this was the largest and most powerful engine option for the F-150 in 1979, used primarily for heavy towing and high-performance needs. It delivered around 245 horsepower and 380 lb-ft of torque, though these numbers could vary slightly based on specific configurations and emissions controls.

These engines were paired with a variety of transmission options, including three-speed or four-speed manuals, and the C6 automatic transmission for higher torque engines. The choice of engine and transmission significantly influenced the truck's performance, fuel economy, and towing capacity.

Keep in mind, the specific output and performance can vary slightly based on factors like the truck's configuration, optional equipment, and condition. If you're looking into a specific model or have a particular use case in mind (like restoration or modification), it might be helpful to look into more detailed sources or forums dedicated to old Ford trucks, as they can offer a wealth of knowledge and specifics tailored to enthusiasts' needs.

The towing capacity of a 1979 Ford F150 can vary significantly depending on the engine size, transmission type, rear axle ratio, and whether the truck is equipped with optional towing packages. Unfortunately, detailed towing capacity specs for vehicles of this era are not as readily available or as standardized as they are for modern vehicles. However, I can provide you with some general estimates and considerations.

Engine Size and Power: Larger engines with more torque, such as the 6.6L V8 (400 CID) or the 7.5L V8 (460 CID), would naturally offer higher towing capacities due to their ability to generate more power and torque. These engines would be more suitable for heavier towing or hauling duties.

Transmission Type: Trucks equipped with automatic transmissions generally have a higher towing capacity than those with manual transmissions due to the automatic's ability to better manage engine power and torque delivery. Rear Axle Ratio: A higher rear axle ratio can also increase towing capacity, as it provides more torque to the wheels at lower speeds, although this can come at the expense of fuel efficiency.

Towing Packages: If the truck was equipped with a factory towing package, it would likely have included features such as a heavier-duty cooling system, stronger frame and suspension components, and possibly even a different rear axle ratio, all of which would contribute to an increased towing capacity.

As a rough estimate, the towing capacity for a 1979 Ford F150 could range from about 4,000 to 7,000 pounds, depending on the factors mentioned above. It's important to note that these are general estimates, and the actual towing capacity could vary. If you're planning to tow with such a vehicle, it's crucial to consider not just the maximum towing capacity but also the weight of the trailer, the distribution of weight on the trailer, and the condition of the vehicle's engine, transmission, brakes, and suspension.

For specific towing capacities and to ensure safe towing practices, it's recommended to consult a professional mechanic who is familiar with old Ford trucks or to refer to original Ford documentation or a reliable restoration guide.


Leave a comment

Please note, comments need to be approved before they are published.

MORE CLASSIC FORD INSIGHTS

1964 FORD FALCON SPRINT

1964 Ford Falcon Sprint a Brief History

1964 Ford Falcon Sprint The 1964 Ford Falcon Sprint is a classic Ford car that holds a special place in the hearts of many car enthusiasts. This vintage Ford model was known for its sleek design, powerful engine, and affordable price. While it may have been over 50 years since its release, the 1964 Ford Falcon Sprint is still a highly sought-after car for collectors and enthusiasts alike. In this article, we will explore the history of this iconic car and discuss the process of restoring one to its former glory. The History of the 1964 Ford Falcon Sprint 1964 Ford Falcon Sprint The Ford Falcon was first introduced in 1960 as a compact car designed to compete with other popular models of the time, such as the Chevrolet Corvair and the Plymouth Valiant. In 1963, Ford released the Falcon Sprint in hardtop and convertible, a sportier version of the original Falcon. The Sprint featured a more powerful 260 cid V8 engine, bucket seats, and a floor-mounted shifter (when equipped with the optional 4 speed), making it a popular choice among car enthusiasts. The Falcon Sprint hardtop was also used in various racing events, solidifying its reputation as a high-performance vehicle. If you're looking to restore a 1964 Ford Falcon Sprint, the first step is to find one for sale. While it may be challenging to find one in good condition, there are still some available for purchase. You can search online for classic car dealerships or browse through online marketplaces such as eBay or Craigslist. It's essential to thoroughly inspect the car before making a purchase, as it may require significant restoration work. Restoring a vintage car like the 1964 Ford Falcon Sprint requires a lot of time, effort, and money. It's crucial to have a clear plan and budget in place before starting the restoration process. The first step is to assess the condition of the car and determine which parts need to be replaced or repaired. It's essential to use original or high-quality reproduction Ford parts to maintain the authenticity and value of the car. Once you have successfully restored your 1964 Ford Falcon Sprint, it's crucial to maintain it properly to preserve its value and performance. Regular maintenance, such as oil changes, tune-ups, and inspections, is essential to keep the car running smoothly. It's also essential to store the car in a dry, climate-controlled environment to prevent rust and other damage. Owning a 1964 Ford Falcon Sprint is more than just having a classic car; it's about reviving nostalgia and preserving a piece of history. Restoring this iconic car is a labor of love that requires dedication and passion. But the end result is a beautiful, high-performance vehicle that will turn heads and bring joy to its owner. Are you a fan of the 1964 Ford Falcon Sprint? Have you restored one yourself? Share your thoughts and experiences in the comments below.
Turn Signal Switch Removal & Replacement

Turn Signal Switch Removal & Replacement

Turn Signal Switch Removal & Replacement Guide Classic Ford Mustang, Falcon, Fairlane, Comet & F-Series Trucks (1960s–1970s) If your turn signals are acting up—or just plain dead—it’s often the switch inside the column calling it quits. The good news? This is a very doable repair with basic tools and a little patience. Below is a step-by-step guide to replacing classic Ford turn signal switches, including popular part numbers like C3OZ-13341-B, C5OZ-13341-B, C5OZ-13341-HQ, C9TZ-13341-C, and C9TZ-13341-USA. Why Replace Your Turn Signal Switch? A worn or failing turn signal switch can cause: Intermittent or non-functioning signals Brake light issues Horn malfunctions (shared circuit in many models) Replacing it restores proper electrical function and keeps your classic Ford safe—and road legal. Tools & Prep Steering wheel puller (TOOL-3600) Small crescent wrench Screwdrivers Dielectric grease Phone (for reference photos—trust me on this one) First rule: Disconnect the battery ground cable. Always. Step-by-Step Removal 1. Remove the Turn Signal Lever Twist the lever out. If it’s stubborn, use a small crescent wrench on the flat spot found on most originals. 2. Remove Horn Button or Ring Push down and turn left to release.⚠️ Go slow—there’s a spring underneath that likes to make a break for freedom. Inspect horn ring retainer Remove horn brush if equipped 3. Pull the Steering Wheel Use your steering wheel puller (TOOL-3600) and set the wheel aside. 4. Document Wiring (Critical Step) Before disconnecting anything: Take clear photos of wire routing and colors Or write them down if you're going old-school Some 1965+ models use connectors that may require a release tool. 5. Disconnect Wiring Under Dash Unplug the turn signal switch harness from beneath the dash. 6. Remove the Turn Signal Switch Back at the column: Remove the (3) mounting screws ONLY Do NOT remove the two large nuts (unless you enjoy fishing dropped studs out of a column…) Carefully pull the switch upward while feeding the wires out of the column. Installation Process 7. Compare Old vs New Switch Before installing: Match wire colors and count Confirm lever compatibility 8. Install New Switch Feed wires down through the column Seat the switch properly Reinstall the (3) retaining screws 9. Reconnect Wiring Plug into under-dash harness Apply dielectric grease to connections for longevity 10. Reassemble Column Reinstall steering wheel Install horn brush (if applicable) Replace spring, horn button/ring Thread in turn signal lever (don’t over tighten) Final Check (Moment of Truth) Reconnect the battery. Now… No smoke? Good sign. No weird noises? Even better. Turn the key and test: Turn signals Brake lights Horn If everything works—you nailed it.If not… well… time to retrace those wiring steps. Pro Tips from the Shop Floor Always photograph wiring before disassembly—memory lies, photos don’t Replace worn horn components while you’re in there Use dielectric grease to prevent future corrosion issues Never force the switch or lever during install Need the Right Turn Signal Switch? At C&G Ford Parts, we’ve been helping restorers get it right since 1978. Every part we carry is built for proper fitment and factory-correct function—because guessing doesn’t belong in a restoration. 👉 Browse our selection of classic Ford turn signal switches and get your signals back in sync.
Getting the Right Pump for Your 1937–48 Ford Flathead V8

Getting the Right Pump for Your 1937–48 Ford Flathead V8

Two Water Pumps, Two Sides: Getting the Right Pump for Your 1937–48 Ford Flathead V8   If you’re new to early Ford Flathead V8s, one look under the hood reveals something a little different from most later engines: there are two water pumps—one on each side of the engine. And no, they aren’t interchangeable. For 1937–48 Ford and Mercury passenger cars and 1937–47 Ford pickups equipped with the V8, C&G Ford Parts offers the two pumps you need: 78-8501-B — Right-Hand Water Pump (Passenger Side)78-8502-B — Left-Hand Water Pump (Driver Side) Knowing which is which matters, especially when you’re replacing only one side.   Why Does a Flathead Ford Have Two Water Pumps? The Flathead V8 cooling system reflects the engine’s distinctive architecture. Instead of using one centrally located water pump, Ford used a pump on each bank of the V8 to circulate coolant through the engine and radiator, keeping in mind each side of the engine has a separate cooling jacket. That makes both pumps important to the cooling system. A worn, leaking or noisy pump on either side deserves attention. On a restoration that has been sitting for years—or an engine with an unknown maintenance history—it’s also worth inspecting both pumps rather than assuming the other side is fine simply because only one is leaking.   Right Hand or Left Hand? Here's the Easy Way to Remember It Early Ford parts terminology identifies left and right from the driver's position looking forward, not from somebody standing in front of the car looking into the engine compartment. So: 78-8501-B — RIGHT HAND = Passenger Side 78-8502-B — LEFT HAND = Driver Side Standing in front of the radiator looking toward the engine can make this seem backwards. When in doubt, think of yourself sitting behind the steering wheel. Driver's side is left. Passenger side is right.   78-8501-B Right-Hand Water Pump C&G part number 78-8501-B is the right-hand, or passenger-side, V8 water pump. It fits 1937–48 Ford and Mercury passenger-car applications and 1937–47 Ford pickup applications as listed in our fitment data. This is a bearing-type pump and includes the mounting gasket. If you're looking under the hood from the driver's seat, this is the pump on your right.   78-8502-B Left-Hand Water Pump C&G part number 78-8502-B is its counterpart for the left-hand, or driver's side, of the engine. It covers the corresponding 1937–48 Ford and Mercury passenger-car and 1937–47 Ford pickup V8 applications. Like the right-hand pump, it is designed as the correct side-specific replacement for these early Ford cooling systems. Remember: 8501 = right/passenger side. 8502 = left/driver side. That little bit of Ford part-number knowledge can come in mighty handy the next time you're staring at an old Flathead.   Don't Ignore the Other Side If one water pump has reached the end of its service life, take a close look at the other one while you're there. Check for coolant leakage, shaft play, bearing noise and signs that the pump has been on the engine for a very long time. Replacing a questionable pump while the cooling system is already drained can be considerably easier than doing the job all over again a few months down the road. That doesn't mean both pumps automatically need replacement every time one fails. It means an old Ford deserves an inspection rather than a guess. The 78-8501-PR Left and Right-hand water pumps are a better deal economically at $189.90 for both sides as a set. While you are inspecting under the hood and the hoses are removed, make sure you check your thermostats for the old flathead.   The Right Parts for Your Early Ford These pumps cover a long and popular stretch of Flathead Ford history—from prewar cars and pickups through the immediate postwar years. Getting the correct pump means checking the year, application and which side of the engine you're working on before placing the order. At C&G Ford Parts, we've been helping people keep old Fords on the road since 1978. If you're unsure which pump fits your Ford, Mercury or pickup, give us a call. You'll talk to people who know these cars and actually drive classics themselves. Need the passenger-side pump? Choose 78-8501-B Right-Hand Water Pump. Need the driver's-side pump? Choose 78-8502-B Left-Hand Water Pump. Need both pumps? Choose the 78-8501-PR Right-Hand and Left-Hand Water Pumps as a set. And if, your Flathead needs both, well… Henry gave you two pumps for a reason. Keep it cool. Keep it Ford. And keep it on the road.