Ford F-Series

FORD F100 HISTORY

In 1953, Ford launched a fresh era of F Series pickups. The 1953 pickups were officially called F-100 and featured sleeker designs with an all-new cab and front end design. This generation of F Series pickups had larger measurements that included 55% larger windshield glass due to its curved design. With the wider cab you can seat 3 full size adults. 1953 Ford also improved chassis now available in 110” and 118” wheelbase (1948-52 is 114”). The gas tank was moved from behind the seat and now mounted on the outside of the frame below the driver’s side of the cab. The upgrades were designed to foster toughness and driving performance. The F Series pickups also took on new names. The F-2 became the F-250. The F-3 was renamed the F-350. Options included a dome light, cigarette lighter, ashtray, sun visors, radio, recirculating air heater and hot water heater. The new name was retained by the F-100 until Ford discontinued production of the F-100 after the 1983 model-year. In 1954 the all-new 239 CID "Y" block engine became available. The 1956 F-100 was celebrated for its perpendicular windshield pillars and its wraparound windshield. Available on the Custom Cab model is a wraparound rear window. The “Y” block 272 was now available as was the 223 6 Cylinder. The gas tank was moved back into the cab behind the seat. Assembly of the F-100 in this time took place mostly in Dearborn, MI. Ford also made approximately 101,000 to 184,000 models of the F100 in Sao Paulo, Brazil.

SECOND GENERATION

The second generation of the Ford F-100 ran from 1957 through 1960. The important styling change for this generation was a lower hood sitting flush on top of the front fenders. Ford launched its tradition of providing two different pick up box styles in this generation. Separate rear fenders were featured on the traditional Stepside design. The new released Styleside layout featured smooth sides as well as a far more streamlined look. New for 1958 was the use of four headlights, Ford continued this until 1960. In 1959, Ford began making the F-100 with a unique four wheel drive. Ahead of this new development, outside makers such as American and Marmon-Herrington and Coleman occasionally converted normal Ford trucks to four wheel drive. The next generation of the vehicles also marked an increase in sales of the optional eight-foot bed for the F-100, the typical length of the bed was six and a half feet. The eight-foot bed eventually eclipsed its smaller counterpart in popularity among F-100 motorists. Assembly continued to take place in the Ford plant in Dearborn, MI.

THE 3RD GENERATION

The new pickups were lower to the ground and wider than earlier versions. 1961 F-100 offered the optional uni-body, which combined the cab and box into one body. Ford discontinued the unibody design at the end of the 1963 production after it fared dismally in the marketplace. 1961 and 1962 Ford still used one piece hood side emblems. In 1963 new body side trim was now available on the styleside trucks with a red painted stripe in the center of the trim. The all new hood side emblem now included a plastic insert with the size of the truck “100”, “250”, “350”. In 1965 designers lowered the cab floor enhancing interior room. 1965 Ford also launched the first of its all new front suspension the "Twin I-Beam". 1965 Also offers a 352 "FE" motor instead of the “Y” block 292. The 6 Cylinder engine is also upgraded from the 223 to the new 240. Ford offered the Ranger option in 1965. The designation referred to your field of options that included an interior optional bucket seats with console and carpeting instead of a rubber floor mat. Ford changed some of its own assembly in this time to a plant in Cuautitlan, Mexico.

FOURTH GENERATION

Ford engineers continued their emphasis on pickups in 1967 that offered a degree of comfort which was similar to a car. 1967 Has new unique hood side emblems. 1967 offered new exterior trim, the body side trim is also new 1-1/4” wide with thin black line top and bottom as well as, available rocker trim. With the new designed cab now includes a new cargo light for the bed at the back of the cab above the rear window. 1968 Changed the hood side emblem to include a reflector. Lower bed side reflectors are standard. The exterior trim is now wider at 1-1/2” wide with the black thin line top and bottom. The Ranger option now includes a grille emblem. New for 1968 is interior door lock knobs. The exterior trim is changed again for 1970. The grille is all new with a plastic inert for either side of the grille. The front of the hood now has a trim going from side to side. The bed side reflector is moved from the lower bed side to the end of the body side trim and now has a light in it. The new Ranger and Ranger XLT trim is now 3-5/8” wide. The new wide trim is available with either black for the Ranger option or woodgrain for the Ranger XLT. 1971 The steering wheel is changed to a two spoke wheel with optional black or woodgrain horn pad.

FIFTH GENERATION OF THE F100 AND INTRODUCTION OF THE F-150

The F-100 underwent major refinements for the fifth generation of the F Series, which ran from 1973 through 1979. Ford released the F-150, a fresh version, in 1973. The F-150 was essentially an F-100 with a spring package in the front and back that enabled the vehicle to carry a heavier load. Ford stopped production of the 4x4 F-100 in 1978. New grille with new plastic inserts for 1973 with the plastic insert now going around the headlight. The XLT option now included a grille emblem. The side trim was now available with a rubber insert down the center of the trim. The side reflectors now had light sockets with the front ones mounted in the front fenders and the rear still at the back of the bed trim. With the all new dash design trucks optioned with factory air conditioning now had vents in the dash for the air to go through and no longer was the air conditioning unit hanging from under the dash. 1974 Ford offered the new “Super Cab” with had a back bench seat and quarter windows behind the door. The new quarter windows were available fixed and with a pop out version. 1977 Offered a new exterior rim called “Race Trak” trim. The trim was a thin molding that started on the front fender at the grille and went down the side of the truck and curved up the bed side to meet the body side trim. Mid year 1978 Ford switch to square headlights which became standard for the F series trucks. Ford stopped producing the venerable F-100 entirely following the 1983 model year.

Fans of Ford F-100 pickups and Ford automobiles in general are motivated to see cgfordparts.com. The site is an excellent resource for locating thousands of old Ford parts now in reproduction. The expert staff members are prepared to answer questions and share their knowledge of Ford restoration.

Leave a comment

Please note, comments need to be approved before they are published.

Name

Email

Comment

Flathead V8 Water Pump and Mount Service Guide

Flathead V8 Water Pump & Mount Service Guide1937–1948 Ford Passenger Car | 1939–1948 Mercury V8 Servicing the cooling system on a 1937–1948 Ford passenger car or 1939–1948 Mercury V8 requires more than just swapping a part. The flathead platform integrates the water pumps, front engine mounts, and cooling hoses in a way that makes access and sequencing important. Whether you’re replacing water pumps, water pump bolts, or addressing motor mounts at the same time, the process benefits from a clear plan. The parts referenced here include: 78-8501-PR – Water Pumps 78-8501-HK – Water Pump Bolts 78-6038-BDK – Motor Mounts These components are commonly serviced together on 37–48 Ford and 39–48 Mercury V8 applications due to their physical proximity and shared mounting areas. Why These Systems Overlap On these flathead V8 engines, the water pumps mount at the front of the block and are positioned near the front motor mount assembly. In many cases, removing the pumps requires relieving load from the mounts. Aging rubber mounts can sag over time, changing engine position slightly and complicating pump removal or installation. Addressing motor mounts during cooling system service can help maintain proper engine alignment. Fitment may vary slightly by model year or chassis configuration. Always confirm application for Ford passenger car versus Mercury V8 before ordering parts. Give us a call or email and we will answer your questions! Basic Removal Sequence A structured approach reduces stress on hardware and surrounding components: Drain CoolantBegin by fully draining the cooling system. Open the radiator petcock and, if equipped, block drains to remove as much coolant as possible. Remove Radiator Hoses (Upper and Lower)Disconnect both hoses from the radiator and water pump outlets. Inspect hose condition during removal. Loosen Motor Mount BoltsThe front motor mount assembly may need to be loosened to allow slight engine movement. Do not fully remove the mount until the engine is properly supported. Support the EngineCarefully jack up the engine using a wood block under the oil pan. The wood block helps distribute load. Raise only enough to relieve tension from the mounts. Remove All Eight Water Pump BoltsEach pump is secured with multiple bolts. Remove all mounting hardware evenly to prevent binding. The water pump bolt kit (78-8501-HK) ensures proper hardware replacement if originals are corroded or worn. *PRO TIP there is a bolt in each of the lower water pump outlets. Once the bolts are removed, the water pumps (78-8501-PR) can be removed from the block. Surfaces should be cleaned thoroughly before re-installation. Motor Mount Considerations The motor mount kit (78-6038-BDK) supports the engine’s front weight and isolates vibration from the frame. When mounts are deteriorated, engine position may shift slightly. Replacing mounts during water pump service is practical because access is already established and the engine is supported. Fitment should always be verified for specific Ford passenger car or Mercury V8 applications within the 1937–1948 and 1939–1948 ranges. Restoration-Focused Approach Flathead cooling system service is straightforward when handled methodically. These engines were designed for serviceability, but age introduces corrosion, hardware fatigue, and rubber deterioration. Replacing water pumps, water pump bolts, and motor mounts as a coordinated service helps maintain structural alignment and cooling integrity. Taking the time to follow proper removal steps protects original components and ensures the flathead V8 continues operating as intended. View our full selection of Flathead V8 Water Pumps and Cooling Components.

Old Ford Parts

Tracing back the gears of time, the story of Ford's iconic "P-R-N-D-L"

Tracing back the gears of time, the story of Ford's iconic "P-R-N-D-L" (affectionately pronounced "prindle") starts in the golden era of automotive innovation. This simple, yet memorable acronym represents the sequence of gears on an automatic transmission: Park, Reverse, Neutral, Drive, and Low. It's a nostalgic nod to the heyday of American car culture, beginning its journey in the 1950s. In 1951, Ford revolutionized their lineup by introducing the first "automatic" transmission in its cars. This was the birth of the P-R-N-D-L sequence, a groundbreaking innovation at the time. Imagine the delight of drivers who, for the first time, could shift gears with a smooth slide of the lever, just once – a far cry from the manual efforts of the past. It should also be noted that unlike todays automatics the early automatics would only start in neutral! The 1950s and 60s were a golden age for Ford. Cars were more than mere transport; they symbolized freedom, style, and the American dream. The P-R-N-D-L was an integral part of this. It wasn't just about the ease of shifting gears; it was about the experience. Each letter was a step in the ritual of driving, a connection between human and machine that modern digital interfaces can't replicate. Fast forward to today, and while cars have evolved with dizzying technology and efficiency, the charm of the classic Ford P-R-N-D-L endures. For enthusiasts and collectors, operating this gearshift isn't just a mechanical action; it's a trip down memory lane, a tactile piece of history that harkens back to the days of chrome, tailfins, and the open road. In essence, the P-R-N-D-L of classic Ford cars is more than just a gear sequence. It's a symbol of a bygone era, a testament to Ford's pioneering spirit, and an enduring part of America's automotive legacy.

Old Ford Trucks

Exploring an American Classic The Ford F100

The Ford F100, a member of the renowned F-Series, has a rich history that spans decades, evolving from a utilitarian work truck to a sought-after classic. Originally designed to meet the demands of post-war America, the F-100 has since become a symbol of vintage style and automotive nostalgia. The F-100 debuted in 1953, a milestone that marked the second generation of Ford's F-Series. Known for its increased dimensions, improved engines, and updated aesthetics, the F-100 was a significant upgrade from its predecessors. It featured a more powerful 215cid inline-six engine, with an option for a 239cid V8, delivering robust performance for the era. The truck boasted a maximum payload capacity of approximately 1,000 to 1,500 pounds, catering to the needs of businesses and individual users alike. In terms of pricing, the F-100 was marketed as an affordable, reliable work truck. Prices started around $1,600, a figure that, when adjusted for inflation, underscores the truck's value proposition. Fast forward to the present, and the Ford F100 occupies a different space in the automotive world. No longer just a work vehicle, it has become a beloved classic, cherished by collectors and enthusiasts. The market for vintage F-100s has seen a significant uptick, with fully restored models fetching prices upwards of $20,000 to $30,000, and exceptional specimens or custom builds going even higher. The appeal of the F-100 in today's market lies in its simplicity, classic design, and the nostalgia it evokes. It's a canvas for customization, with a thriving aftermarket offering everything from original replacement parts to modern upgrades. The versatility of the F-100 makes it a favorite among those looking to create a personalized classic that combines vintage charm with modern performance. The demand for original equipment specifications remains high, with purists seeking to restore F-100s to their factory glory. This desire for authenticity reflects a broader trend in the classic car market, where originality often equates to higher value. Conclusion The Ford F-100's journey from a practical utility vehicle to a cherished classic is a testament to its enduring appeal. In the current market, it embodies a blend of history, style, and the enduring legacy of Ford's commitment to utility and innovation. Whether restored to its original specifications or customized to modern tastes, the F-100 remains a beloved piece of American automotive history, with a vibrant community of enthusiasts keeping its spirit alive.