11A-9350-E6, 6 VOLT ELECTRIC FUEL PUMP

INTRODUCING A NEW ITEM, THE 1959 PASSENGER AND RANCHERO PARK LIGHT HOUSINGS!  

1960–1965 Ford & Mercury Door Seal Installation Guide (C0DZ-6220530-PR) Application This guide applies to vehicles using door seal set C0DZ-6220530-PR, including: 1960–1965 Falcon / Comet – 2 Door Sedan 1960–1965 Falcon / Comet – 2 Door Wagon 1960–1965 Ranchero 1960–1965 Sedan Delivery These vehicles use perimeter door seal mounted directly to the door shell. Proper installation is critical for wind noise reduction, water control, and correct door closing tension. Original Shop Notes 3M-8001 Glue C0DZ-6220530-PR 60-65 Falcon/Comet 2DR Sedan 60-65 Falcon/Comet 2DR Wagon 60-65 Ranchero 60-65 Sedan Delivery Installation notes: Remove old door seals Clean inside door surface Clean door seals Test fit door seals, maybe tape seals to door Put glue on door, work in sections These notes capture the core sequence used in many restoration shops when replacing early-1960s Ford door seals. Door Seal Replacement Procedure 1. Remove the Existing Door Seals Start by removing the original seals from the door. On vehicles from this era, the rubber seal is typically glued directly to the door rather than clipped or retained with molded fasteners. Over decades the adhesive hardens and the rubber may tear during removal. Work slowly along the channel and peel the seal away from the metal surface. Remaining adhesive residue or fragments of the old rubber should also be removed during this stage so the new seal can sit flat against the door. 2. Clean the Door Mounting Surface “Clean door surface.” This step is critical before any adhesive is applied. The inner perimeter flange where the seals mounts must be free of: Old adhesive Rubber residue Dirt or oil A clean mounting surface allows the adhesive to bond properly and prevents the seal from lifting later. Pay particular attention to corners and tight radius where residue tends to remain. 3. Clean the New Door Seal “Clean door seals.” Even new reproduction seals can carry mold release residue from manufacturing or dust from storage and handling. Wiping the seal before installation ensures the adhesive bonds to the rubber surface properly. This step is simple but helps prevent long-term separation between the rubber and the door. 4. Test Fit the Door Seal Before applying adhesive: “Test fit door seals, maybe tape seals to door.” Dry fitting the seal verifies: Correct orientation of the molded corners Proper length around the perimeter Alignment with the door flange Many restorers temporarily secure the seal with masking tape during this step. Taping allows you to check how the seal sits around the entire perimeter before committing to adhesive. If the seal appears twisted or stretched, reposition it during the test fit rather than after glue has been applied. 5. Apply Adhesive in Sections “Put glue on door, work in sections.” Using 3M-8001 adhesive, apply glue to the door flange where the seal will sit. Rather than coating the entire perimeter at once, work in manageable sections. Installing in sections helps: Maintain correct seal alignment Prevent adhesive from setting before placement Allow the rubber to seat evenly along the channel Press the seals firmly into place as each section is installed, ensuring the molded lip follows the door contour. Continue this process around the door perimeter until the entire seal is secured. Why Section Installation Matters Early Ford door seals are molded to follow the door perimeter precisely. Installing the seal gradually allows the rubber to settle into the correct position while adhesive is still workable. Attempting to glue the entire perimeter at once often results in: Misalignment at corners Excess adhesive squeeze-out Seal tension that causes doors to sit high Working in stages helps maintain proper positioning and factory-style fitment. When Door Seal Replacement Is Necessary Door seals commonly requires replacement when you encounter: Wind noise while driving Water intrusion during rain Hardened or cracked rubber Missing or deteriorated seal sections These symptoms are typical on vehicles where the original rubber has aged for decades.   Fitment Reminder Door seal configuration can vary by body style and model year. Confirm vehicle body type and model year before ordering replacement seals. Explore our full selection of classic Ford door seals and restoration rubber components to support proper body sealing and factory-correct restoration.

Why This Job Matters This isn’t just about lights—it’s about safety and reliability. A fresh harness eliminates voltage drops, intermittent faults, and those “works when it feels like it” gremlins. It’s one of those upgrades that doesn’t show at the car show, but you’ll feel it every time you drive.