Classic ford parts

INSTALLING A CLASSIC FORD DISTRIBUTOR INTO OLD FORD TRUCKS AND CARS

37-41 Old Ford Trucks, Old Ford Car and Old Mercury Car Distributor

INSTALLING A CLASSIC FORD DISTRIBUTOR

1932-1941 Old Ford Trucks, 1932-1941 Ford Passenger Cars and 1939-1941 Mercury Cars with original V8 distributor:

1. Check inner caps one at a time to make sure they fit distributor housing, sand them if needed. Also check to make sure once installed rotor does not hit the inner cap. After fitting inner caps put inner and outer caps together with the spark plug wires and set aside.

2. Mount coil to distributor making sure coil brush makes contact with rotor and copper contact is not bent.

3. Make sure the mounting surface is clean and there is nothing in the camshaft slot where the distributor mounts. Check to make sure mounting bolt threads are clean and free of dirt, set bolts on top of engine for easy reach.

4. Time to mount the distributor. Put gasket on base of distributor, you can put a small amount of sealant on the gasket. Place distributor on to timing cover using fingers to turn rotor to make sure distributor is correctly seated in the camshaft. The distributor will mount flat to the timing cover when correctly installed. If the distributor is not seated correctly you can crack the distributor case when you tighten the bolts. Now you can put the three mounting bolts in and tighten. Do not over tighten(snug).

5. Install inner/outer caps to the distributor and pop the bail over to hold in place.

6. Install vacuum line to distributor.

1941-47 (6 Cylinder “G” Engine) Old Ford Trucks and Passenger Cars, 1942-1947 Old Ford Trucks and 1942-1948 Passenger Cars/Mercury Cars (V8):

1. Make sure the mounting surface is clean and there is nothing in the camshaft slot where the distributor mounts. Check to make sure mounting bolt threads are clean and free of dirt, set bolts on top of engine for easy reach.

2. Place the rotor on distributor and mount distributor cap and turn rotor slowly to make sure the rotor does not hit the inner cap. If rotor hits cap lightly file end of rotor till it clears. Remove distributor cap and set aside. Leave rotor on distributor.

3. Time to mount the distributor. Put gasket on base of distributor, you can put a small amount of sealant on the gasket, be sure not to get sealant on vacuum rubber grommet. Place distributor on to timing cover using fingers to turn rotor to make sure distributor is correctly seated in the camshaft. The distributor will mount flat to the timing cover when correctly installed. If the distributor is not seated correctly you can crack the distributor case when you tighten the bolts. Now you can put the two mounting bolts in and tighten. Do not over tighten(snug).

4. Install distributor cap and pop clips on for 42 crab cap. If you have a 46-48 with the inner and outer cap you will have to install plug wires into cap first before installing caps on distributor.

Leave a comment

Please note, comments need to be approved before they are published.

Name

Email

Comment

A classic old ford scene featuring 1940's Americana

Old Ford Cars

The Classic Ford Parts Niche and Americana

The world of classic Ford parts is a niche fueled by a unique blend of nostalgia, engineering marvel, and a deep-seated passion for automotive history. This niche isn't just about maintaining or restoring old vehicles; it's about preserving a legacy, a piece of Americana that has shaped and been shaped by decades of innovation and culture. At the heart of this niche are the classic Fords themselves - from the groundbreaking Model T, the first car to be mass-produced, to the Mustang, an icon of American muscle and the F series pick ups which supply the backbone of America. Each model represents a different era, a distinct style of engineering and design. Restoring these vehicles is more than a hobby; it's a journey back in time, an attempt to capture the essence of an era long gone. For those immersed in the classic Ford parts niche, the hunt components is a significant part of the excitement. These enthusiasts spend countless hours searching through auto flea markets, online forums, and specialty shops for that perfect part. The joy of finding a rare, original component can be as exhilarating as driving the restored vehicle itself. The community aspect of this niche is incredibly strong. Across the world, classic Ford owners and restorers come together, both online and in person, to share stories, exchange knowledge, and offer support. Car shows and meet-ups turn into celebrations of these automotive treasures, where the beauty and craftsmanship of classic Fords are displayed with pride. Moreover, the classic Ford parts niche is not just about the past; it's about sustainability. In a world increasingly concerned with environmental impact, restoring and maintaining older vehicles is a form of recycling, giving new life to old Fords that might otherwise be forgotten relics. In essence, the classic Ford parts niche is more than a collection of old cars and their components. It's a testament to the enduring impact of Ford's innovations on automotive culture. It's a community bound by a shared passion for the art of restoration, a reverence for history, and the thrill of bringing a piece of that history back to life. For many, it's not just a hobby; it's a way of connecting with the past and preserving it for future generations. Here at C&G Ford Parts we specialize in reproduction Ford parts.

Old Ford Trucks

1979 Ford F150

1979 Ford F150 The 1979 Ford F150 stands as a significant chapter in the storied history of Ford trucks. Known for its durability, classic design, and utility, the '79 F150 is a beloved model among enthusiasts of classic Ford automobiles. Specifications Engine Options: The 1979 F150 came with various engine options, including: 4.9L 300 Inline-6: A reliable workhorse known for its longevity. 5.0L 302 V8: Offered a balance of power and efficiency. 5.8L 351M V8 and 6.6L 400 V8: These larger engines were preferred for heavier towing and payload capacities. Transmission: Standard: 3-speed manual. Optional: 4-speed manual and 3-speed automatic. Dimensions: Wheelbase: Ranged from 117 inches (regular cab, short bed) to 155 inches (SuperCab, long bed). Length: Varied based on the model, from 188.5 inches to 235 inches. Width: Approximately 79 inches. Towing and Payload: Depended on the engine and configuration, with the larger engines supporting greater capacities. Part Numbers: Locating specific part numbers for a vehicle as old as the 1979 F150 can be challenging. However, some common parts include: Brake Pads: D84-2 Oil Filter: FL-1A Spark Plugs: AGSF32. For more specific parts and their numbers, enthusiasts often refer to vintage Ford parts catalogs or online forums. A great place to get real people to talk parts with, is C&G Ford Parts in Escondido, California. Production Numbers: Ford does not publicly release detailed production numbers by year and model. However, it's known that the F-Series was America's best-selling truck in 1979, contributing significantly to the series' overall sales. The F150's popularity in this era helped solidify its legacy in the Ford lineup. Accessories and Customization: The 1979 F150 was often customized and accessorized, reflecting the owner's needs and style. Popular accessories included: Chrome Bumpers: For enhanced aesthetics. Toolboxes: Fitted in the bed for utility. Lift Kits: Many owners lifted their trucks for off-road capability or for a more imposing road presence. Custom Paint Jobs: Reflecting the era's penchant for personalization. Conclusion: The 1979 Ford F150 remains a beloved classic. Its robust construction, range of engine options, and classic styling have ensured its lasting appeal. While specific part numbers and production figures can be elusive, the truck's impact on the automotive landscape is undeniable. Whether restored to its original glory or customized for modern roads, the '79 F150 continues to be a symbol of Americana and the enduring legacy of Ford trucks.

Old Ford Cars

CLASSIC MUSTANG PARTS

There’s nothing like the sound of a 289 V8 with a four-barrel carburetor purring down the street. When you’ve got the ponies galloping under the hood of a 1966 Mustang, it doesn’t matter if the sun is shining or the rain is pouring - it’s a beautiful day when you’re behind the wheel of a classic. Classic cars, especially ones like the Mustang, are always head turners. It’s no wonder your car sounds good. You’ve kept your beauty running smoothly with classic Mustang parts whenever you need to replace something. Sometimes, when you own a classic, just like with the newer model cars, a problem can develop unexpectedly. The problems can be small or large. For example, you might start to notice that your Mustang doesn’t have the same gallop it used to have. You don’t see what the problem is until one day, you see smoke like you’ve never seen before. When you see white smoke coming from the exhaust of the car, you need to get it home and check the dipstick to see if there’s a distinctive milky appearance in the oil. That could mean a blown head gasket. When you realize that there’s a blown head gasket, you know that in order to get the car up and running in the best of shape, you’ve got to find an auto store that sells classic Mustang parts. You may not have one local, you may have to order online, but whatever you have to do to get parts for your car, it’s worth any effort. You don’t want to compromise with just any parts seller, come to the best here at C&G Ford Parts! A lot of times, you’ll see shops advertise that their replacement parts for your classic car are so “identical looking” that you can’t see a visual difference. You may not be able to see a visual difference with a knock off part, but you can certainly tell a difference in how the car runs and in how long that part will last. Buying classic Mustang parts isn’t just for when you need to fix something on the car. These are what car enthusiasts look for when they’re restoring a classic to its former glory - and if you ever decide to sell you car, it should have parts made just for it. It doesn’t matter if it’s a small job like replacing your gas cap or a big job like replacing the windshield seal - you’ll get more mileage and less headaches by choosing classic Mustang parts from C&G Ford Parts, always choose the best.